home *** CD-ROM | disk | FTP | other *** search
/ NOVA - For the NeXT Workstation / NOVA - For the NeXT Workstation.iso / Documents / NeXTAnswers / hardware.196 < prev    next >
Text File  |  1992-02-06  |  4KB  |  100 lines

  1. {\rtf0\ansi{\fonttbl\f0\fswiss Helvetica;\f1\fnil Times-Roman;}
  2. \paperw11440
  3. \paperh9000
  4. \margl120
  5. \margr120
  6. {\colortbl\red0\green0\blue0;}
  7. \pard\tx533\tx1067\tx1601\tx2135\tx2668\tx3202\tx3736\tx4270\tx4803\tx5337\f0\b0\i0\ul0\fs24 power amps watts hardware boards\
  8. \
  9. Q:  What is the power consumption of the NeXT computer system?\
  10. Q:  How many watts of power are available to a plug-in board?\
  11. \
  12. A:  Typical power consumption of the 030 NeXT cube and monitor  (not printer): 150 Watts, 2 amps \
  13.         Maximum power consumption  (not printer):  about 300 Watts, 5 amps.  \
  14.       Power consumption of  printer: \
  15.         In standby mode (not printing):  110 Watts at either 115 or 220 Volts\
  16.         Peak power while printing:    640 Watts at 115 Volts, 1240 W at 220 V\
  17.       Printing increases the total current draw of the system up to 10 amps.\
  18. \
  19. Regarding add-on boards in 030 cube systems: we conservatively specify 20 watts per card.  Depending on system loading, the total power can go as high as 25 watts.  The basic limitation is our power supply, which allows 12 amps of +5 for the three expansion slots (assuming maximum loading on the CPU and two disk drives).   If your board consumes too much power, the power supply will probably shut down to protect the cube, if your board hasn't fried first.  However, using a board that exceeds the spec will void the warranty on any NeXT parts that are damaged.  You can't redistribute the available 60W total differently -- each slot really only does get about 20W. \
  20. \
  21. Approximately 0.5 amps total of + and - 12 volts are also available.\
  22. \
  23. \
  24. Measurements on color and monochrome NeXTstations showed the following power requirements, with no external peripherals attached to the serial or DSP ports.   Note that the monitors for the monochrome systems are powered from the internal (cpu box) power supply, whereas the color monitors are powered from a separate AC power cord.    Power requirements for the 040 CPU board in the NeXTcube should be identical to those for the monochrome NeXTstation.\
  25.  
  26. \fc0 \
  27. NeXTstation:\
  28.             CPU Board        CPU Board\
  29.             8 MB DRAM        8 MB DRAM\
  30.             Monitor            Monitor\
  31.                             200 MB drive\
  32.                             Floppy drive\
  33. ========================================\
  34.     +12V        2.0A                3.5A\
  35.     -12V        2.5A                2.5A\
  36.     5.0V            3.5A                4.5A\
  37. ========================================\
  38. \
  39. NeXTstation Color:\
  40.             CPU Board        CPU Board\
  41.             32 MB DRAM        32 MB DRAM\
  42.                             200 MB drive\
  43.                             Floppy drive\
  44. ========================================\
  45.     +12V        0.4A                1.5A\
  46.     -12V        0.1A                0.1A\
  47.     5.0V            4.0A                5.0A\
  48. ========================================\
  49.  
  50. \
  51.  
  52. The power supply that comes with both NeXTstations provides the following:\
  53. \
  54.     +5 V            7A\
  55.     +12V        4A\
  56.     -12V        3A\
  57.     \
  58.  
  59. \pard\tx520\tx1060\tx1600\tx2120\tx2660\tx3200\tx3720\tx4260\tx4800\tx5320\f1\fs28 \
  60. \
  61.  
  62. \f0\fs24 The following additional, approximate power requirements for the NeXTstation (monochrome) and NeXTcube systems were derived from specifications and analysis, but were not measured directly:\
  63.         \
  64.         CPU    :\
  65.             +5V:\
  66.                 Idle                    2A\
  67.                 Peak                5A\
  68.             +12V\
  69.                 (including Net)        0.5A\
  70.             -12V\
  71.                 (for datacomm,etc.)    0.1A\
  72.                 \
  73.         If the board is driving a monitor, add 2.5A to the +12V and -12V current requirements.\
  74.         \
  75.         \
  76.         Floppy:\
  77.             Standby power             100mW\
  78.             +5V:\
  79.                 Running current         0.5 A\
  80.                 Peak current            1 A\
  81.         \
  82.         SCSI disk:\
  83.             Average power             10 - 15W\
  84.             +12V:\
  85.  
  86. \fc0                 on 105 and 200 Mb drives:    2A peak\
  87.                 \
  88.  
  89. \pard\tx1140\tx2300\tx3440\tx4600\tx5760\tx6900\tx8060\tx9200\tx10360\tx11520\f1\fs28 \
  90.  
  91. \pard\tx533\tx1067\tx1601\tx2135\tx2668\tx3202\tx3736\tx4270\tx4803\tx5337\f0\fs24 \
  92. See also hardware.101.\
  93. \
  94. QA196\
  95. \
  96. Valid for 1.0 \
  97. Valid for 2.0 \
  98. \
  99.  
  100.